AgniJeet offers the most advanced and internationally approved Cable Fire Proofing Solutions.
We can even offer a custom-mix of various Supportive and Complimentary Fire Stopping solutions for your specific requirement.

Cable Fire Protection
Peace of Mind

Our Cable Fire Proofing solutions comes with many International Approvals. We deal in various MNC brands like HILTI, 3M, Stanvac, etc. and offers the most Economical Solution.

Having all internationl and local approvals ensures peace of mind for client andend-user.
download brochure.

(Very Basic Skill Level)

Easy  Workmanship
Most Versatile Solution

Our Cable Fire Proofing Paint comes as a Single Pack product. It is a very Versatile Product which just needs to be directly applied from the drum. Almost a Zero VOC product.

A person with basic masonry skill could easily do the application of this product. Just mix the paint and spray /brush!
download brochure.

(Solution for All Needs)

Fire Stop Mix
Vast Array of Fire Stops

Apart from Cable Fire Proofing Paints, we offer Fire Stop solutions for various requirement, like Electrical Shafts, Duct, Fire Wall Opening (Vertical & Horizontal), Curtain Wall Gaps, etc.

Solutions include Fire Mortar, Mineral Wool, Fire Sealants, Intumescent Paints, Fire Pillows, etc. ; based on Gypsum, Vermiculite & Intumescent technology.
download brochure.

In the event of a Short Circuit or other Fire accident, an unprotected Cable will burn and even propage the fire along its run. The smoke fumes that are formed are even more dangeround and hazardous.
Cable Fire Retardant Paint is Totally Reliable. because there are no electrical or mechanical activating devices to fail, no human error to be concerned about, no tanks to refill and no periodic maintenance.

AgniJeet Cable Coating is one of the most economical and maintenance-free ways to protect cables from fire in electrical equipment, substations, cable galleries, cable spreader, control rooms and other high density cable areas.

Passive fire protection is the first line of defence in the preventing the spread of fire. As opposed to active fire suppression, such as fire extinguishers and sprinkler systems, passive fire protection doesn't actively put the fire out. Its aim is to contain the fire and smoke within a compartment of the building, allowing the safe evacuation of the property, and preventing further damage to the structure. If the location of the fire prevents the evacuation of all areas, then passive fire systems provide protection to any trapped personnel allowing the fire brigade to attend the scene, and effect the safe removal of those trapped. An important piece of fire protection advice to remember is that passive fire protection can, and does, save lives as well as property.

Cable Fire Protection
Passive fire protection materials insulate Cable structures from the effects of the high temperatures that may be generated in fire. The main function of Cable Coating system is to prevent flame propagation and stop loss of integrity along vertical and horizontal cable ways. It will also delay short circuit for up to 90 minutes, whereby circuit integrity depends on the distance of the cables from fire and the incurred temperature. Our Cable Coating products are easily applied by conventional methods such as Fireproofing Spray and brush, as well as by hand.
Flame Retardents are NOT Fire Proofing Products.
Fire Proofing Products will give your Structural Member a Fire Resistance Rating. Flame retardents will simply inhibit the spread of flames across a surface. BS476 -parts 6 & 7 defines two Classes of Flame Spread: Class 0 & Class 1.
  • Class 0 is a fire propagation test, which means that the coated material not only prevents the spread of flame across its surface, but also stops fire from penetrating into the material for up to 13 minutes
  • Class 1 is granted when a fire close to the material only blackens at the point of contact and does not allow the fire to spread across it
Intumescent coatings are paint like materials which are inert at low temperatures but which provide insulation as a result of a complex chemical reaction at temperatures typically of about 200-250°C. At these temperatures the properties of Cable will not be affected. As a result of this reaction they swell and provide an expanded layer of low conductivity char. Intumescent coatings can be divided into two broad families: thin film and thick film. Thin film materials are either solvent based or water based and are mainly used for building fires. Thick film intumescent coatings were originally developed for the off-shore and hydrocarbon industries but have been modified for use in buildings.
Thin film intumescent coating systems generally have three components: a primer, a basecoat (the part which reacts in the fire) and a sealer coat. The basecoat usually comprises the following ingredients:
  • A catalyst which decomposes to produce a mineral acid such as phosphoric acid.
  • A carbonific such as starch which combines with the mineral acid to form a carbonaceous char.
  • A binder or resin which softens at a predetermined temperature.
  • A spumific agent which decomposes together with the melting of the binder, to liberate large volumes of non-flammable gases. These gases include carbon dioxide, ammonia and water vapour. The production of these gases causes the carbonaceous char to swell or foam and expand to provide an insulating layer many times the original coating thickness.
They are mainly used in buildings where the fire resistance requirements are 30, 60 and 90 minutes. In recent years, a number of products have been developed which can provide 120 minutes fire resistance . They can be applied either on-site or off-site. In general, most on-site application is carried out using water based materials. However, where the structure to which the material is applied is not to have an end use in a dry, heated (C1) environment, solvent based materials are commonly used. Solvent based materials also tend to be able to cover a wider range of section factors than water based materials and can be used on-site to protect smaller sections requiring high thicknesses. Both solvent based and water based coatings can be used to achieve attractive surface finishes. If a decorative or bespoke finish is required, this should be included in the specification. Thin film intumescents have the added advantages that they can easily cover complex shapes and post-protection service installation is relatively simple. Typical expansion ratios are about 50:1, i.e. a 1mm thick coating will expand to about 50mm when affected by fire. Detailed guidance on the specification and installation of site applied, thin film intumescent coatings is available from the Association for Specialist Fire Protection.
Thick film intumescent coatings are usually epoxy based and typically have a much higher dry film thickness than thin film alternatives. These materials are tough and durable and were originally developed for use with hydrocarbon fires, where the test heating regime is much more severe than that used for most industrial and commercial applications. A number of manufacturers have modified their materials for use in cellulosic fires. These modified materials are usually used in situations where the benefits of intumescent coatings in terms of appearance, weight and thickness are required but where circumstances are too severe, or maintenance too difficult, to allow the use of thin film materials . Typical recent examples have occurred in external Cable in high rise buildings and exposed marine environments. Expansion ratios for thick film intumescents are much lower than for thin film materials, typically about 5:1. Aesthetic finishes are possible and it can also be supplied in the form of preformed casings. Thick film intumescent coatings can also be applied off-site.

Also known as Cementitious or Vermiculite Fireproofing

Spray protection is extensively used across the world, mostly owning to it being the cheapest method for Cable Fire Protection. It has the advantage that it can be used to cover complex shapes and details and also that costs do not increase significantly with increases in protection thickness. This is because much of the cost of application is in the labour and equipment and a minority is in the cost of the material. Some materials can also be used in external and hydrocarbon fire applications.
Sprays are generally not suitable for aesthetic purposes. Also, application is a wet trade and this may have impacts on other site operations. Allowance may have to be made in costing for the possible requirement for prevention of overspray.
Boards are widely used for structural fire protection in the UK. They are used both where the protection system is in full view and where it is hidden. They offer the specifier a clean, boxed appearance and have the additional advantages that application is a dry trade and may not have significant impacts on other activities. Also, boards are factory manufactured and thicknesses can be guaranteed. Furthermore, boards can be applied on unpainted Cablework.
There are broadly two families of board protection, lightweight and heavyweight. Lightweight boards are typically 150-250kg/m³ and are not usually suitable for decorative finishes. They are typically used where aesthetics are not important and are cheaper than heavyweight equivalents. Heavyweight boards are usually in the range 700-950kg/m³ and will generally accept decorative finishes. They are typically used where aesthetics are important.

Both types of board may be used in limited external conditions but the advice of the manufacturer should be sought.
Well, that is a decission that the architect, structural consultant and client whould take in tandem. The merits and demerits of each of the system has been detailed above. A general thumb rule is as below:
  • Where there is need for aesthetics, opt for Intumescent Fireproofing.
  • Where the speed of execution is important (as in fast application), opt for Intumescent Fireproofing.
  • Where the structures are hidden under false cealing or cladding, opt for Vermiculite Fireproofing.
  • Where economical consideration are paramount, opt for Vermiculite Fireproofing.
  • Where the premises cannot be shutdown for application, opt for Fire Resistive Boards.

This is only a helping guideline.

AgniJeet has expertise in handling all these three methods of Cable Fire Proofing.
We can even offer a custom-mix of them as the optimum economical solution for your specific requirement.

Contact us for any clarifications you may require.